AGMA 6009 - Search Results
Articles About AGMA 6009
Articles are sorted by RELEVANCE. Sort by Date.
AGMA and members of the Metal Powder Industries Federation (MPIF) are three years into a joint project to develop specifications and an information sheet on rating powder metal gears. According to committee vice chairman Glen A. Moore of Burgess-Norton Mfg. Co., the first phase of the project, the publication of AGMA Standard "6009-AXX, Specifications for Powder Metallurgy Gears," should be completed in late 1996 or early 1997.
One of the best ways to learn the ISO 6336 gear rating system is to recalculate the capacity of a few existing designs and to compare the ISO 6336 calculated capacity to your experience with those designs and to other rating methods. For these articles, I'll assume that you have a copy of ISO 6336, you have chosen a design for which you have manufacturing drawings and an existing gear capacity calculation according to AGMA 2001 or another method. I'll also assume that you have converted dimensions, loads, etc. into the SI system of measurement.
The American Gear Manufacturers Association (AGMA) is accredited by the American National Standards Institute (ANSI) to write all U.S. standards on gearing. However, in response to the growing interest in a global marketplace, AGMA became involved with the International Standards Organization (ISO) several years ago, first as an observer in the late 1970s and then as a participant, starting in the early 1980s. In 1993, AGMA became Secretariat (or administrator) for Technical Committee 60 of ISO, which administers ISO gear standards development.
This is the third article in a series exploring the new ISO 6336 gear rating standard and its methods of calculation. The opinions expressed herein are htose of the author as an individual. They do not represent the opinions of any organization of which he is a member.
AGMA925–A03 scuffing risk predictions for a series of spur and helical gear sets of transmissions used in commercial vehicles ranging from SAE Class 3 through Class 8.
Another year, another AGMA Fall Technical Conference. But this is no ho-hum event. Not when every year, the conference attracts some of the greatest mechanical engineering minds on the planet, along with representatives of the world’s greatest manufacturing entities. And who knows—perhaps one day there will be an extraterrestrial contingent—the science is that good. And all of it readily applicable to real-world manufacturing.
The wind turbine industry has been plagued with gearbox failures, which cause repair costs, legal expenses, lost energy production and environmental pollution.
The major focus of the American Gear Manufacturers Association standards activity has been the accurate determination of a gearbox's ability to transmit a specified amount of power for a given amount of time. The need for a "level playing field" in the critical arena was one of the reasons the association was formed in the first place. Over the past 85 years, AGMA committees have spent countless hours "discussing" the best ways to calculate the rating of a gear set, often arguing vigorously over factors that varied the resulting answers by fractions of a percentage point. While all that "science" was being debated in test labs and conference rooms all over the country, out industry's customers were conducting their own experiments through the daily operation of gear-driven equipment of all types.
Long-time readers of these pages will know that I have always felt strongly about the subject of professional education. There's nothing more important for an individual's career development than keeping up with current technology. likewise, there's nothing more important that a company can do for itself and it employees than seeing to it they have the professional education they need. Giving people the educational tools they need to do their jobs is a necessary ingredient for success.
A few months ago at the AGMA management seminar, I was surprised by the feverish note taking that went on at a presentation on marketing. The sight reminded me that while many of us in the gear industry are good engineers, designers, and mangers, we are often not as familiar - or comfortable - with less concrete concepts, such as marketing.
Five years of effort by AGMA came to fruition in January with the publishing of a report from the Department of Commerce. This "National Security Assessment of the U.S. Gear Industry" indicates that if serious measures are not taken, the gear industry's future is in jeopardy. It also sets the tone for confronting major challenges now looming large in our industry.
With all the heated debate and hoopla surrounding ISO 9000 certification, everyone seems to have an opinion about whether to sign up. Executives in the gear industry are flooded with information and ideas that often seem at odds. Gear Technology asked AGMA executive director Joe T. Franklin, Jr. to give an industry perspective on the pros and cons of ISO 9000 certification.
AGMA has an excellent Training School for Gear Manufacturing. It's a great product providing a great service to the gear industry. Thus far we've educated 117 employees from 71 companies; students range from new hires with no experience to company presidents. Essentially every class since December, 1992, has been sold out.
"Gear Train" is a new Gear Technology section focusing on training and education in the gear industry. For the first installment, we've focused on AGMA's online and video training programs.
Standards are unlike gears themselves: mundane, but complex, ubiquitous and absolutely vital. Standards are a lingua franca, providing a common language with reference points for evaluating product reliability and performance for manufacturers and users. The standards development process provides a scientific forum for discussion of product design, materials and applications, which can lead to product improvement. Standards can also be a powerful marketing tool for either penetrating new markets or protecting established ones.
Who wants or needs technical details about gearing? Who cares about it? Three out of every four people who are reading this magazine make up at least 75% of those who have an interest in the subject. The members of AGMA, EUROTRANS, JGMA and JSIM have an interest. All the people attending the Gear Expo in Detroit have an interest. Clearly, however, the people with the most pressing interest in our industry are our customers, the end users of gear products. The unfortunate reality, though, is that in many cases, these customers don't even know that's what they want.
It's nice to see old friends. It's also advantageous to make new ones. Gear Expo has always been a family reunion of sorts, but it's first and foremost an opportunity to show off the latest and greatest technologies that are impacting the gear industry today. With this in mind, Gear Technology recently spoke with those responsible for putting the Fall Technical Meeting (FTM) and Gear Expo 2013 together in Indianapolis.
If you haven’t already done so, you should make plans to attend Gear Expo in September. It’s a unique and important show, and you should take advantage of it.
I’ve just come back from the AGMA annual meeting in Napa, California, where I had a great time visiting with friends and colleagues in the gear industry. As always, the annual meeting was a great opportunity to network and meet with other AGMA members.
The geometry of the bevel gear is quite complicated to describe mathematically, and much of the overall surface topology of the tooth flank is dependent on the machine settings and cutting method employed. AGMA 929-A06 — Calculation of Bevel Gear Top Land and Guidance on Cutter Edge Radius — lays out a practical approach for predicting the approximate top-land thicknesses at certain points of interest — regardless of the exact machine settings that will generate the tooth form. The points of interest that AGMA 929-A06 address consist of toe, mean, heel, and point of involute lengthwise curvature. The following method expands upon the concepts described in AGMA 929-A06 to allow the user to calculate not only the top-land thickness, but the more general case as well, i.e. — normal tooth thickness anywhere along the face and profile of the bevel gear tooth. This method does not rely on any additional machine settings; only basic geometry of the cutter, blank, and teeth are required to calculate fairly accurate tooth thicknesses. The tooth thicknesses are then transformed into a point cloud describing both the convex and concave flanks in a global, Cartesian coordinate system. These points can be utilized in any modern computer-aided design software package to assist in the generation of a 3D solid model; all pertinent tooth macrogeometry can be closely simulated using this technique. A case study will be presented evaluating the accuracy of the point cloud data compared to a physical part.
The 25th anniversary is the silver. The 50th is the gold. The 75th is the diamond. But what symbolizes the 100th?
your life and in your professional career is an inflection point for you to take stock of where you came from and where you are going.
Lastest news from around the industry.
AGMA President Joe Franklin is stepping down after some 24 years on the job. He graciously took the time to answer some questions from Gear Technology Senior Editor Jack McGuinn regarding his tenure.
How should we consider random helix angle errors fHβ and housing machining errors when calculating KHβ? What is a reasonable approach?
This issue, GT Extras brings you "Heat Treat and Induction Hardening of Industrial Gears," a treasure trove of heat treating related technical articles and a call for help in preparation for AGMA's 100th anniversary.
In today’s globalized manufacturing, all industrial products having dimensional constraints must undergo conformity specifications assessments on a regular basis. Consequently, (standardization) associated with GD&T (geometrical dimensioning and tolerancing) should be un-ambiguous and based on common, accepted rules. Of course gears - and their mechanical assemblies - are special items, widely present in industrial applications where energy conversion and power transmission are involved.
The new chairman of the AGMA Technical Division Executive Committee explains what's involved in the process of developing technical standards at the AGMA.
The AGMA/ABMA Annual Meeting took place April 10-12 in St. Petersburg, Florida. Between committee meetings, networking opportunities and social events, many individuals in the gear industry were presented awards.
Charlie Fischer, VP Technical Division, retiring end of April
So there is little chance that they need the same software to assist with their work. Gone are the days when companies wrote their own code and process engineers thumbed the same tattered reference book.
The face load factor is one of the most important items for a gear strength calculation. Current standards propose formulae for face load factor, but they are not always appropriate. AGMA 927 proposes a simpler and quicker algorithm that doesn't require a contact analysis calculation. This paper explains how this algorithm can be applied for gear rating procedures.
In Part I differences in pitting ratings between AGMA 218, the draft ISO standard 6336, and BS 436:1986 were examined. In this part bending strength ratings are compared. All the standards base the bending strength on the Lewis equation; the ratings differ in the use and number of modification factors. A comprehensive design survey is carried out to examine practical differences between the rating methods presented in the standards, and the results are shown in graphical form.
The authors of last issue's article comparing AGMA, ISO and BS methods for Pitting Resistance Ratings are commended. Trying to compare various methods of rating gears is like hitting a moving target in a thick forest. The use of different symbols, presentations, terminology, and definitions in these standards makes it very difficult. But the greatest problem lies with the authors' use of older versions of these documents. ISO drafts and AGMA standards have evolved at the same time their work was accomplished and edited.
Despite the many things being done to promote manufacturing nationwide, there still remains an acute need for gear-specific training, remedial or otherwise.
Listing of papers to be presented and activities for the 2007 AGMA Fall Technical Meeting.
The AGMA pavilion was a hot spot at October's PTC-Asia show in Shanghai, as evidenced by the intense quoting reported by exhibitors.
Step forward now to help yourself and your industry.
When you graduated from school and made your way into the world, you probably thought you’d learned everything you needed to know to be successful. But those of us who’ve been out in the workforce for some time know that you never stop learning.
The world is full of acronyms. At work, the inbox reveals e-mails from the AWEA, SAE, MPIF and AMT. On the weekends, Saturday mornings are consumed by activities involving the AYSO, PTA, YMCA or DMV. It’s a struggle to determine what organization does what and why we should care in the first place.
The organizers of Gear Expo 2007 promise to combine the most popular features of shows past with some innovations for this year’s attendees. By the time the show closes on October 10, the association hopes its targeted 175 exhibitors walk away with new insights leading to profitability and renewed contacts.
"One of the reasons AGMA has been successful over our 93-year history is that the association’s agenda, programs and activities reflect the voices of our members," says Joe T. Franklin, Jr., AGMA President.
As the international business community grows closer together, the need for understanding differences between national and international gear rating standards becomes increasingly important for U.S. gear manufacturers competing in the world market.
What do glam and avant garde rock star Brian Eno, AGMA and Seattle Gear Works have in common? Admittedly, not much. But there is a connection of sorts.
“The gear marketplace is a global marketplace.” Bill Bradley says it easily, with no special emphasis. The vice president of AGMA’s technical division sees the statement as an obvious fact.
Industrial gear standards have been used to support reliability through the specification of requirements for design, manufacturing and verification. The consensus development of an international wind turbine gearbox standard is an example where gear products can be used in reliable mechanical systems today. This has been achieved through progressive changes in gear technology, gear design methods and the continual development and refinement of gearbox standards.
Events from SME and AGMA, along with news from the gear industry.
Gear Technology talks with AGMA's president about the association and its role in the gear industry.
Arlin Perry, president of Comer Industries, talks about his tenure as chairman of the AGMA Foundation and its role in supporting the industry.
Dr. Phil Terry, chairman of the AGMA Technical Division Executive Committee, talks about the standards-making process.
October 5-8, 1986 AGMA Fall technical Conference & Gearing Exhibit September 17-19, 1986 Ohio State University Gear Noise Seminar November 11-13, 1986 SME Gear Processing and Manufacturing Clinic November 19-21, 1986 Seminar: Gear System Design for Minimum Noise
Herman Riccio, Chicago Gear Works President, to Retire; Gleason Opens MI Sales Office; American Pfauter hires Steve Peterson; plus AGMA's technical calendar for the Fall of 1984.
A change has taken place within the industry that is going to have an enormous effect on the marketing, sales, and purchasing of gear manufacturing and related equipment. This change was the American Gear Manufacturers' Association, first biennial combination technical conference and machine tool minishow.
For the last few years, the market has been tough for the U.S. gear industry. That statement will cause no one any surprise. The debate is about what to do. One sure sign of this is the enormous attention Congress and the federal government are now placing on "competitiveness."
AGMA introduced ANSI/AGMA 2015–2–A06— Accuracy Classification System: Radial System for Cylindrical Gears, in 2006 as the first major rewrite of the double-flank accuracy standard in over 18 years. This document explains concerns related to the use of ANSI/AGMA 2015–2–A06 as an accuracy classification system and recommends a revised system that can be of more service to the gearing industry.
It is often easy for those outside of the gear industry to get the impression that nothing is changing in our business. After all, all illustrated bimonthly by the covers of this very journal the making of gears has been with us for centuries. However, nothing could be further from the truth.
At a time when there are many pressures on the Gear Industry and its representative Association, the American Gear Manufacturers Association, it seems particularly appropriate that Gear Technology - The Journal of Gear Manufacturing appears. AGMA is particularly pleased to have the opportunity to write the first editorial for this magazine.
The AGMA Fall Technical Meeting provides an opportunity to share ideas with others on the design, analysis, manufacturing and application of gears, gear drives, and related products, as well as associated processes and procedures.
A recap of the AGMA 2010 Fall Technical Meeting.
AGMA Chairman David Ballard discusses what it means to be an AGMA member.
Gary A. Bish, director of product design technology for Horsburgh & Scott, discusses his role as chairman of the AGMA mill gearing committee.
Chairman Todd Praneis of Cotta Transmission describes the activities of AGMA's Enclosed Drives technical committee.
AGMA president Joe T. Franklin Jr. talks about how the AGMA Gear Expo has grown and changed since its beginnings as a table-top show in 1987.
AGMA Flexible Couplings committee chairman Glenn C. Pokrandt gives an update about standards and other documents under development.
A study of AGMA 218, the draft ISO standard 6336, and BS 436: 1986 methods for rating gear tooth strength and surface durability for metallic spur and helical gears is presented. A comparison of the standards mainly focuses on fundamental formula and influence factors, such as the load distribution factor, geometry factor, and others. No attempt is made to qualify or judge the standards other than to comment on the facilities or lack of them in each standard reviewed. In Part I a comparison of pitting resistance ratings is made, and in the subsequent issue, Part II will deal with bending stress ratings and comparisons of designs.