Home | Advertise | Subscribe

Magazine | Newsletter | Product Alerts | Blog

South Bend Gear - Search Results

Articles About South Bend Gear


1 Industry News (March/April 2013)

The complete Industry News section from the March/April 2013 issue of Gear Technology.

2 Influence of Geometrical Parameters on the Gear Scuffing Criterion - Part I (March/April 1987)

The load capacity rating of gears had its beginning in the 18th century at Leiden University when Prof. Pieter van Musschenbroek systematically tested the wooden teeth of windmill gears, applying the bending strength formula published by Galilei one century earlier. In the next centuries several scientists improved or extended the formula, and recently a Draft International Standard could be presented.

3 Computer-Aided Design of the Stress Analysis of an Internal Spur Gear (May/June 1988)

Although there is plenty of information and data on the determination of geometry factors and bending strength of external gear teeth, the computation methods regarding internal gear design are less accessible. most of today's designs adopt the formulas for external gears and incorporate some kind of correction factors for internal gears. However, this design method is only an approximation because of the differences between internal gears and external gears. Indeed, the tooth shape of internal gears is different from that of external gears. One has a concave curve, while the other has a convex curve.

4 Tooth Strength Study of Spur Planet Gears (September/October 1986)

In the design of any new gear drive, the performance of previous similar designs is very carefully considered. In the course of evaluating one such new design, the authors were faced with the task of comparing it with two similar existing systems, both of which were operating quite successfully. A problem arose, however, when it was realized that the bending stress levels of the two baselines differed substantially. In order to investigate these differences and realistically compare them to the proposed new design, a three-dimensional finite-element method (FEM) approach was applied to all three gears.

5 Endurance Limit for Contact Stress in Gears (October/November 1984)

With the publishing of various ISO draft standards relating to gear rating procedures, there has been much discussion in technical papers concerning the various load modification factors. One of the most basic of parameters affecting the rating of gears, namely the endurance limit for either contact or bending stress, has not, however, attracted a great deal of attention.

6 Analysis and Testing of Gears with Asymmetric Involute Tooth Form and Optimized Fillet Form for Potential Application in Helicopter Main Drives (June/July 2011)

Gears with an asymmetric involute gear tooth form were analyzed to determine their bending and contact stresses relative to symmetric involute gear tooth designs, which are representative of helicopter main-drive gears.

7 A Rational Procedure for Designing Minimum-Weight Gears (November/December 1991)

A simple, closed-form procedure is presented for designing minimum-weight spur and helical gearsets. The procedure includes methods for optimizing addendum modification for maximum pitting and wear resistance, bending strength, or scuffing resistance.

8 Investigation of the Strength of Gear Teeth (November/December 1992)

To mechanical engineers, the strength of gear teeth is a question of constant recurrence, and although the problem to be solved is quite elementary in character, probably no other question could be raised upon which such a diversity of opinion exists, and in support of which such an array of rules and authorities might be quoted. In 1879, Mr. John H. Cooper, the author of a well-known work on "Belting," made an examination of the subject and found there were then in existence about forty-eight well-established rules for horsepower and working strength, sanctioned by some twenty-four authorities, and differing from each other in extreme causes of 500%. Since then, a number of new rules have been added, but as no rules have been given which take account of the actual tooth forms in common use, and as no attempt has been made to include in any formula the working stress on the material so that the engineer may see at once upon what assumption a given result is based, I trust I may be pardoned for suggesting that a further investigation is necessary or desirable.

9 Tooth Root Optimization of Powder Metal Gears - Reducing Stress from Bending and Transient Loads (June/July 2013)

This paper will provide examples of stress levels from conventional root design using a hob and stress levels using an optimized root design that is now possible with PM manufacturing. The paper will also investigate how PM can reduce stresses in the root from transient loads generated by abusive driving.

10 Setting Load Parameters for Viable Fatigue Testing of Gears in Powertrain Axles Part I: Single-Reduction Axles (August 2014)

This presentation introduces a new procedure that - derived from exact calculations - aids in determining the parameters of the validation testing of spiral bevel and hypoid gears in single-reduction axles.

11 Calculating Spur and Helical Gear Capacity with ISO 6336 (November/December 1998)

This is the third article in a series exploring the new ISO 6336 gear rating standard and its methods of calculation. The opinions expressed herein are htose of the author as an individual. They do not represent the opinions of any organization of which he is a member.

12 Gear Crack Propagation Investigations (November/December 1997)

A common design goal for gears in helicopter or turboprop power transmission is reduced weight. To help meet this goal, some gear designs use thin rims. Rims that are too thin, however, may lead to bending fatigue problems and cracks. The most common methods of gear design and analysis are based on standards published by the American Gear Manufacturers Association. Included in the standards are rating formulas for gear tooth bending to prevent crack initiation (Ref. 1). These standards can include the effect of rim thickness on tooth bending fatigue (Ref 2.). The standards, however, do not indicate the crack propagation path or the remaining life once a crack has started. Fracture mechanics has developed into a useful discipline for predicting strength and life of cracked structures.

13 1992 Marks Important Gear Design Milestone: Lewis Bending Strenth Equations Now 100 Years old (November/December 1992)

Columbus' first voyage to the Americas is not the only anniversary worthy of celebration this year. In 1892, on October 15, Wilfred Lewis gave an address to the Engineer's Club of Philadelphia, whose significance, while not as great as that of Columbus' voyage, had important results for the gearing community. In this address, Lewis first publicly outlined his formula for computing bending stress in gear teeth, a formula still in use today.

14 Bending Fatigue, Impact and Pitting Resistance of Ausform-Finished PM Gears (June 2010)

The powder metal (P/M) process is making inroads in automotive transmission applications due to substantially lower costs of P/M-steel components for high-volume production, as compared to wrought or forged steel parts. Although P/M gears are increasingly used in powered hand tools, gear pumps and as accessory components in automotive transmissions, P/M-steel gears are currently in limited use in vehicle transmission applications. The primary objective of this project was to develop high-strength P/M-steel gears with bending fatigue, impact resistance and pitting fatigue performance equivalent to current wrought steel gears.

15 Methodology for Translating Single-Tooth Bending Fatigue Data to be Comparable to Running Gear Data (March/April 2008)

A method to extrapolate running gear bending strength data from STF results for comparing bending performance of different materials and processes.

16 Bending Fatigue Tests of Helicopter Case Carburized Gears: Influence on Material, Design and Manufacturing Parameters (November/December 2009)

A single tooth bending (STB) test procedure has been developed to optimally map gear design parameters. Also, a test program on case-carburized, aerospace standard gears has been conceived and performed in order to appreciate the influence of various technological parameters on fatigue resistance and to draw the curve shape up to the gigacycle region.

17 An Investigation of the Influence of Shaft Misalignment on Bending Stresses of Helical Gears with Lead Crown (November/December 2008)

In this study, the combined influence of shaft misalignments and gear lead crown on load distribution and tooth bending stresses is investigated. Upon conclusion, the experimental results are correlated with predictions of a gear load distribution model, and recommendations are provided for optimal lead crown in a given misalignment condition.

18 The Elementary Theory for the Synthesis of Constant Direction Pointing Chariots (or Rotation Neutralizers) (November/December 1988)

The south-pointing chariot exhibited at the Smithsonian Institution, Washington, D.C., (circa 2600 BC)is shown in Fig. 1. Although the mechanism is ancient, it is by no means either primitive or simplistic. The pin-tooth gears drive a complex system, wherein the monk on the top of the chariot continues to point in a preset direction, no matter what direction the vehicle in moved, without a slip of the wheels.(1)

19 Curvilinear Cylindrical Gears (May/June 1988)

The curved tooth cylindrical gear is one of ancient design. Samples which date from the period of the Warring State (475-221 BC) have been excavated from archeological sites in China. One such sample is now on display in the Xi'an Clay figures of Warriors and Horses Exhibition Hall. This example is about 3/4" in diameter and made of bronze. It was used in the famous model, "Ancient Chinese Vehicle With a Wooden Figure Always Pointing to the South." Although this early gear is handmade and somewhat crude, it is a viable model.

20 Global Positioning System: The Early Years (January/February 2010)

Before retiring from St. Louis Gear in 2000, Roy Harmon liked to tinker. Since the customer base at the time was seasonal, Harmon was looking for a project to keep himself busy. The engineer decided to challenge himself by designing a “South Pointing Chariot,” a device he had read about in the book The Evolution of the Gear Art by Darle Dudley.

21 Dynamic Analysis of Straight and Involute Tooth Form (July/August 1985)

The effect of load speed on straight and involute tooth forms is studied using several finite-element models.

22 Evaluation of Bending Strength of Carburized Gears (May/June 2004)

The aim of our research is to clearly show the influence of defects on the bending fatigue strength of gear teeth. Carburized gears have many types of defects, such as non-martensitic layers, inclusions, tool marks, etc. It is well known that high strength gear teeth break from defects in their materials, so it’s important to know which defect limits the strength of a gear.

23 Generating Interchangeable 20-Degree Spur Gear Sets with Circular Fillets to Increase Load Carrying Capacity (July/August 2006)

This article presents a new spur gear 20-degree design that works interchangeably with the standard 20-degree system and achieves increased tooth bending strength and hence load carrying capacity.

24 Asymmetric Teeth: Bending Stress Calculation (March/April 2007)

This article includes a brief summary of the characteristics of involute asymmetric teeth and the problems connected with the related bending tests.

25 Tooth-Bending Effects in Plastic Spur Gears (September/October 2007)

This paper describes the investigation of a steel-and-plastic gear transmission and presents a new hypothesis on the governing mechanism in the wear of plastic gears.

26 True Bending Stress in Spur Gears (August 2007)

In this paper, an accurate FEM analysis has been done of the “true” stress at tooth root of spur gears in the function of the gear geometry. The obtained results confirm the importance of these differences.

27 Systematic Investigations on the Influence of Case Depth on the Pitting and Bending Strength of Case Carburized Gears (July/August 2005)

The gear designer needs to know how to determine an appropriate case depth for a gear application in order to guarantee the required load capacity.

News Items About South Bend Gear

1 Fozo Named Operations Manager at South Bend Gear (August 9, 2011)
Doug Fozo has been named operations manager for South Bend Gear, a new joint venture of Schafer Gear Works, Inc. with headquarters in Sou... Read News

2 Paul Morrisson Joins South Bend Gear (July 31, 2012)
Paul Morrisson has joined South Bend Gear, LLC as operations manager of the recently built manufacturing plant producing gears for heavy-... Read News

3 Somaschini Announces Buyout of South Bend Gear (February 7, 2013)
Somaschini S.p.A., headquartered in Trescore Balneario (Bergamo) Italy, announces the purchase on Nov. 30th from Schafer Gear Works Inc. ... Read News