wind turbines | Gear Technology Magazine

IGS to Increase Wind Gearbox Torque Density

July 15, 2022

Ruben Carranza Fernandez and Dr.-Ing. Thomas Tobie

To increase cost efficiency in wind turbines, the wind industry has seen a significant rise in power density and an increase in the overall size of geared components. Current designs for multimegawatt turbines demand levelized cost of energy (LCOE) reduction, and the gearbox is a key part of this process. Since fatigue failures nearly always occur at or near the surface, where the stresses are greatest, the surface condition strongly affects the gear life. Consequently, an improved surface condition effectively avoids major redesign or increased material cost due to an increase in part size. Additional finishing methods such as shot peening (SP) and superfinishing (SF) significantly increase the gear load capacity, but these effects have not yet been adequately considered in the current ISO 6336 standard or in any other gear standards. The combination of SP followed by SF will be described here as an “improved gear surface” (IGS).

Influence of Planet Carrier Misalignments on the Operational Behavior of Planetary Gearboxes

July 1, 2020

This study deals with the modeling and consideration of misalignments in planetary gearboxes in the optimization and design process. Procedures for taking into account misalignments in cylindrical gearboxes are standardized and established in industry. Misalignments of central elements like carrier, sun gear or ring gear in planetary gearboxes, cause varying contact positions and variable loads, depending on the angular position of the central elements. This load, which is variable over the circumference, is not taken into account in the standardized procedures, despite its effects on the loads on the gears.

New Guideline for Determining the Reliability of Planetary/Spur Gear Units

May 1, 2020

In the wind power industry, the reliability of powertrain components plays a major role. Especially in multi-megawatt offshore applications, an unplanned replacement of drivetrain components can lead to extremely high costs. Hence, the expectation of wind farm operators is to forecast the system reliability. Under the leadership of the VDMA (Mechanical Engineering Industry Association), the standardization paper 23904 "Reliability Assessment for Wind Turbines" was published in October 2019.

Understanding Oil Analysis: How it Can Improve Reliability of Wind Turbine Gearboxes

November 1, 2013

Historically, wind turbine gearbox failures have plagued the industry. Yet an effective oil analysis program will increase the reliability and availability of your machinery, while minimizing maintenance costs associated with oil change-outs, labor, repairs and downtime. Practical action steps are presented here to improve reliability.

Turbine Gearbox Inspection - Steady Work in a Shaky Wind Market

August 1, 2013

Having outlasted the worldwide Great Recession, the Global Wind Energy Council (GWEC) forecasts a constant growth in wind energy, i.e.: "increase in worldwide capacity to 460,000 MW by 2015."

Growing Pains - Renewables Hang on in Turbulent Energy Market

June 1, 2012

The turbines are still spinning. They’re spinning on large wind farms in the Great Plains, offshore in the Atlantic and even underwater where strong tidal currents offer new energy solutions. These turbines spin regularly while politicians and policy makers— tied up in discussions on tax incentives, economic recovery and a lot of finger pointing—sit idle. Much like the auto and aerospace industries of years past, renewable energy is coping with its own set of growing pains. Analysts still feel confident that clean energy will play a significant role in the future of manufacturing—it’s just not going to play the role envisioned four to five years ago.

Flank Breakage on Gears for Energy Systems

November 1, 2011

Gear flank breakage can be observed on edge zone-hardened gears. It occurs, for example, on bevel gears for water turbines, on spur gears for wind energy converters and on single- and double-helical gears for other industrial applications.

Comparison of Test Rig and Field Measurement Results on Gearboxes for Wind Turbines

October 1, 2011

This article describes some of the most important tests for prototypes conducted at Winergy AG during the product development process. It will demonstrate that the measurement results on the test rig for load distribution are in accordance with the turbine measurements.

Wind Turbines: Clean Energy, but Energy Efficient

June 1, 2011

Jack McGuinn

We talked energy efficiency with some major players in the lubricants industry— but with a focus on their products’ impact regarding energy efficiency of gears and gearboxes in wind turbines.

Wind Standard Closer to Completion

March 1, 2011

Jack McGuinn

Faithful Gear Technology readers may recall that our July 2009 issue contained an update of the deliberations provided by Bill Bradley. Now, almost two years later, there is an ISO/IEC wind turbine gearbox standard out for draft international standard ballot (ballot closes 2011-05-17).