Cylindrical Gears - Search Results
Articles About Cylindrical Gears
Articles are sorted by RELEVANCE. Sort by Date.
Spur cylindrical gears are usually cut using a hob and therefore present an essentially straight face to which crowning can be added to prevent edge contact. Rather than using a rack or hob, it is possible to cut cylindrical gears with a face mill cutter. In the following presentation, these gears are termed "spurved," i.e. â€” a contraction of "spur" and "curved."
A validated simulation model is used to analyze more in-depth investigations into the influence of a stochastic course of the pitch error on the quasi-static excitation behavior.
Why is there so much emphasis on the tooth contact pattern for bevel gears in the assembled condition and not so for cylindrical gears, etc?
This article also appears as Chapter 1 in the Gleason Corporation publication "Advanced Bevel Gear Technology." Gearing Principles in Cylindrical and Straight Bevel Gears The purpose of gears is to transmit motion and torque from one shaft to another. That transmission normally has to occur with a constant ratio, the lowest possible disturbances and the highest possible efficiency. Tooth profile, length and shape are derived from those requirements.
This proposed standard would not make any recommendations regarding the required quality for any application. The intent is to establish standard pre-finish quality classes for typical finishing operations, which only include the inspection elements that are important to properly evaluate pre-finish gear quality as it applies to the finishing operation. It would be the responsibility of the manufacturing/process engineer, quality engineer, or other responsible individual to establish the required pre-finish quality class for their application.
It has long been known that the skiving process for machining internal gears is multiple times faster than shaping, and more flexible than broaching, due to skiving's continuous chip removal capability. However, skiving has always presented a challenge to machines and tools. With the relatively low dynamic stiffness in the gear trains of mechanical machines, as well as the fast wear of uncoated cutters, skiving of cylindrical gears never achieved acceptance in shaping or hobbing, until recently.
Power Skiving with Integrated Cutter Resharpening
In this paper local tooth contact analysis and standard calculation are used to determine the load capacity for the failure modes pitting, tooth root breakage, micropitting, and tooth flank fracture; analogies and differences between both approaches are shown. An example gearset is introduced to show the optimization potential that arises from using a combination of both methods. Difficulties in combining local approaches with standard methods are indicated. The example calculation demonstrates a valid possibility to optimize the gear design by using local tooth contact analysis while satisfying the requirement of documenting the load carrying capacity by standard calculations.
Alongside the macro test parameters on tooth flanks for profile and tooth traces, surface properties (roughness) play a decisive role in ensuring proper toothed gear function. This article addresses roughness measurement systems on tooth flanks. In addition to universal test equipment, modified test equipment based on the profile method for use on gears is addressed in particular. The equipment application here refers to cylindrical gear flanks and bevel gear flanks. The most important roughness parameters, as well as the implementation of the precise measurement procedure will also be described under consideration of the applicable DIN EN ISO standards as well as the current VDI/VDE Directive 2612 Sheet 5.
In this article the authors present a loaded tooth contact analysis (LTCA) method for asymmetric gears that provides an accurate and efficient design tool for analyzing and comparing designs. The presented method is implemented in SMT's MASTA software. The authors also present an example comparative study using this tool for an automotive application.
This paper presents approximate and accurate methods to generate solid models of involute cylindrical gears using Autodesk Inventor 3-D CAD software.
The curved tooth cylindrical gear is one of ancient design. Samples which date from the period of the Warring State (475-221 BC) have been excavated from archeological sites in China. One such sample is now on display in the Xi'an Clay figures of Warriors and Horses Exhibition Hall. This example is about 3/4" in diameter and made of bronze. It was used in the famous model, "Ancient Chinese Vehicle With a Wooden Figure Always Pointing to the South." Although this early gear is handmade and somewhat crude, it is a viable model.
This paper presents an original method to compute the loaded mechanical behavior of polymer gears. Polymer gears can be used without lubricant, have quieter mesh, are more resistant to corrosion, and are lighter in weight. Therefore their application fields are continually increasing. Nevertheless, the mechanical behavior of polymer materials is very complex because it depends on time, history of displacement and temperature. In addition, for several polymers, humidity is another factor to be taken into account. The particular case of polyamide 6.6 is studied in this paper.
Curved face width (CFW) spur gears are not popular in the gear industry. But these non-metallic gears have advantages over standard spur gears: higher contact ratio, higher tooth stiffness, and lower contact and bending stresses.
Designing a gear set implies a considerable effort in the determination of the geometry that fulfills the requirements of load capacity, reliability, durability, size, etc. When the objective is to design a new set of gears, there are many alternatives for the design, and the designer has the freedom to choose among them. Reverse engineering implies an even bigger challenge to the designer, because the problem involves already manufactured gears whose geometry is generally unknown. In this case, the designer needs to know the exact geometry of the actual gears in order to have a reference for the design.
AGMA introduced ANSI/AGMA 2015â€“2â€“A06â€” Accuracy Classification System: Radial System for Cylindrical Gears, in 2006 as the first major rewrite of the double-flank accuracy standard in over 18 years. This document explains concerns related to the use of ANSI/AGMA 2015â€“2â€“A06 as an accuracy classification system and recommends a revised system that can be of more service to the gearing industry.
Changes in the third edition of parts 1, 2, 3, 5 and 6 compared to the previous edition (from the year 2006 for parts 1, 2, 3, 6 and from the year 2003 for part 5).
The first part of this publication series covered the general basics of involute gearing and applied the generating principle of cylindrical gears analogous to angular gear axis arrangements the kinematic coupling conditions between the two mating members have been postulated in three rules. Entering the world of bevel gears also required to dwell somewhat on the definition of conjugacy. The second part is devoted to the different generating gears and the chain of kinematic relationships between the gear - gear generator - pinion generator and pinion.
During the revision of ISO 1328-1:2013 Cylindrical gears â€” ISO system of flank tolerance classification, ISO Technical Committee TC 60 WG2 delegates discussed proposals that the standard should be modified to ensure that it is compatible with the ISO Geometrical Product Specification (GPS) series of standards (Refs. 1-3). This seems sensible because the gears are geometrical components, but after reviewing the implications, it was rejected because ISO TC 60 WG2 did not think the gear manufacturing industry was ready for such a radical change in measurement strategy. The feasibility of the implementation of gears into the GPS matrix of standards has been carried out and the results conclude that this is practical, provided some key issues related to measurement uncertainty and establishing appropriate KPIs are addressed.
The paper is not the proof of a discovery, but it is the description of a method: the optimization of the microgeometry for cylindrical gears. The method has been applied and described on some transmissions with helical gears and compound epicyclic, used on different hybrid vehicles. However, the method is also valid for industrial gearboxes.
Gear hobbing is one of the most productive manufacturing processes for cylindrical gears. The quality of the gears is a result of the tool quality, the precision of the workpiece, tool clamping and kinematics of the machine. The dry gear hobbing process allows machining of gears with a quality according to the DIN standard up to IT 5. To evaluate which gear quality is possible to machine with a given clamping and hob, it is useful to simulate the process in advance.
Chamfering and deburring of cylindrical gears does not get much love from manufacturers. The process is seen as a necessary evil since it is adding cost without adding value. However, there are good reasons for not underrating this important auxiliary process. Chamfering and deburring takes care of several issues which may come up during the manufacture of quality gears.
Hobbing is a continuous gear generation process widely used in the industry for high or low volume production of external cylindrical gears. Depending on the tooth size, gears and splines are hobbed in a single pass or in a two-pass cycle consisting of a roughing cut followed by a finishing cut. State-of-the-art hobbing machines have the capability to vary cutting parameters between first and second cut so that a different formula is used to calculate cycle times for single-cut and double-cut hobbing.
High-speed machining using carbide has been used for some decades for milling and turning operations. The intermittent character of the gear cutting process has delayed the use of carbide tools in gear manufacturing. Carbide was found at first to be too brittle for interrupted cutting actions. In the meantime, however, a number of different carbide grades were developed. The first successful studies in carbide hobbing of cylindrical gears were completed during the mid-80s, but still did not lead to a breakthrough in the use of carbide cutting tools for gear production. Since the carbide was quite expensive and the tool life was too short, a TiN-coated, high-speed steel hob was more economical than an uncoated carbide hob.
Rochester, NY - Gleason Corporation has acquired the assets of Hurth Maschinen and Werkzeuge GmbH, the designer and builder of cylindrical (parallel-axis) gear-making machinery and tooling based in Munich, Germany. The addition of Hurth gear shaving machines and tooling and gear honing machines will further broaden Gleason's expanding product line for manufacturers of cylindrical gears.
Minimizing gear losses caused by churning, windage and mesh friction is important if plant operating costs and environmental impact are to be minimized. This paper concentrates on mesh friction losses and associated scuffing risk. It describes the preliminary results from using a validated, 3-D Finite Element Analysis (FEA) and Tooth Contact Analysis (TCA) program to optimize cylindrical gears for low friction losses without compromising transmission error (TE), noise and power density. Some case studies and generic procedures for minimizing losses are presented. Future development and further validation work is discussed.
This article discusses the potential effects observed for different antiwear and EP chemistry on the micropitting of cylindrical gears.
VDI has created a data exchange format that allows for the electronic exchange of all geometric parameters for cylindrical gears.
We know that for cylindrical gears we have the standard DIN 3964 for defining deviations of shaft center distance and shaft position tolerances of casings. And for bevel gears? Is there some specific standard for defining deviations of center distance and shaft position tolerances of casings (orthogonal shafts), as DIN 3964 do?
News Items About Cylindrical Gears
1 GWJ Technology Offers Enhanced Calculation of Cylindrical Gears (July 14, 2020)
GWJ Technology GmbH from Germany has updated the calculation module for cylindrical gears in its web-based software solution eAssistant.I... Read News
2 GWJ Technology Offers New Calculation Modules for Cylindrical Gears (June 22, 2016)
GWJ Technology GmbH, a manufacturer of calculation software for machine elements and gearboxes, has upgraded its web-based calculation so... Read News
3 KISSsoft Offers Strength Analysis for Cylindrical Gears (March 24, 2016)
The strength calculation method specified in Lloyd's Register:2013 has now been implemented. This specific standard for ships is now ... Read News
4 KISSsoft Extends Contact Analysis for Cylindrical Gears (October 9, 2013)
The contact analysis for cylindrical gears in KISSsoft (module ZA30) has been extended and improved. Experience gained from a comparison ... Read News
5 Combined Process Machine Completes Cylindrical Gears (January 26, 2010)
The Agilus 180TH multi-functional machine from Gleason performs turning, drilling, milling, hobbing and chamfering/deburring operatio... Read News
6 Gleasons Newest Threaded Wheel Grinder Delivers Faster Floor-to-Floor Times for Cylindrical Gears up to 300 mm (February 13, 2007)
The 300 TWG from Gleason Corp. is designed to deliver fast floor-to-floor times for grinding of cylindrical gears with a diameter up to 3... Read News