Drivetrain Research Center - Search Results
Articles About Drivetrain Research Center
Articles are sorted by RELEVANCE. Sort by Date.
It is said that â€śThe squeaky wheel gets the grease.â€ť Ok, but what about gear noise? We talked to three experts with considerable knowledge and experience in this area.
A look at several American organizations doing cutting edge gear-related research for aerospace applications.
The popular perception today is that technological advancement is an engine running almost out of control. New products and processes are developing faster than we can keep up with them, as anyone who has had a new computer system crash into obsolescence practically before it's out of the box can tell you. But that's not the case everywhere. Transmission technology, for example.
In 1993, M & M Precision Systems was awarded a three-year, partial grant from the Advanced Technology Program of the Department of Commerce's National Institute of Standards and Technology (NIST). Working with Pennsylvania State University, M&M embarked on a technology development project to advance gear measurement capabilities to levels of accuracy never before achieved.
How does one determine the center of a worm and a worm wheel? Also, what are the differences between the common worm tooth forms?
While external involute gears are very tolerant of center distance variations, what are the center distance constraints for internal gears?
With the right selection of nonstandard center distance and tool shifting, it may be possible to use standard tools to improve the gear set capacity with a considerable reduction in cost when compared to the use of special tools.
Delta Research upgrades its Gleason Metrology Workhorses to meet the development requirements of the latest electrical drive vehicles.
Oil-out conditions, or conditions in which an aircraft is operating without any oil in its gearbox or transmission, are devastating for an aircraft's hardware. Even the sturdiest gears usually can't last 30 minutes under such conditions before they catastrophically fail, and the whole system usually follows shortly after. That doesn't leave pilots with a whole lot of time to find a suitable location to land in the case of an oil-out emergency.
If you've got a gear performance problem, the Gear Research Institute (GRI) is here to help you. Since inception in 1982, GRI has been a primarily industry sponsored, experimentation driven research facility. Whether establishing the fatigue life of gears or evaluating the impact of manufacturing processes on the performance of gears, GRI has pioneered methods and procedures for characterizing such properties that are accepted by the aerospace, vehicle and other industry sectors.
In a capitalist society, the way things usually work is that government and academia focus on research and development, while industry focuses on commercialization. The result is an increasingly wide disconnect in the applied research sector, which deals primarily with technology development and demonstration.
The essence of designing gears is often by necessity risk-averse, given that many of them are used in applications where loss of life is a distinct possibility. The Gear Research Institute (GRI) at The Pennsylvania State University conducts risk reduction testing with the same goal in mind - whether it be gears in fighter jets, Ferris wheels, tanks, or countless other gear-reliant vehicles and machinery.
When, in 1980, OSU professor Donald R. Houser created the Gear and Power Transmission Research Laboratory - then known as the Gear Dynamics and Gear and Power Transmission Laboratory (GearLab) - he did so with the seed money provided by just three companies. Thirty-three years out, the lab has continued to grow, impress andâ€”most importantly - succeed; it now boasts a roster of some 50 sponsoring companies and government agencies.
In March 1989, the U.S. Trade Representative requested the U.S. International Trade Commission to conduct an investigation and prepare a report on the competitive position of the U.S. gear industry in U.S. and global markets.
Hoechst Technical Polymers has expanded its interests in plastic gears with the introduction of the new Plastic Gear Evaluation and Research machine P-Gear. The machine is the centerpiece of the company's continuing efforts to promote and develop the use of plastic gears in higher-powered applications.
In May of this year the U.S. International Trade Commission made public its Report to the President on the condition of the U.S. gear industry. This 200+ page document is the result of a two-year study by the commission, with the help of the AGMA staff and members. It is the most comprehensive and current analytical coverage of the industry conditions and tends presently available. Because of the importance of this report to the industry, GEAR TECHNOLOGY is devoting a good portion of this issue to reprinting the Executive Summary for our readers.
Chicago- Results of recent studies on residual stress in gear hobbing, hobbing without lubricants and heat treating were reported by representatives of INFAC (Instrumented Factory for Gears) at an industry briefing in March of this year.
Recent history has taught us that global competition has become tougher and is a major concern of American gear manufacturers from abroad have invaded American markets with products designed in an environment where management of technology has been practiced effectively. If American companies intend to compete in the changing world market, they must acquire the technologies that will allow them to do so.
These are changing times for industry. Trauma and uncertainty are always a part of change, and change is not always for the better. Change is usually forced, most frequently by competition. Our competitive free enterprise system should be able to respond to competition because that's its basis. These are critical years. If we do not respond effectively to change and competition, it could be disasterous.
Gear research seems to be thriving. Between September 10th and October 17th, 120 papers about gears were presented at three conferences in Milwaukee, Boston, and Washington, to a total audience of about 400. The authors were from nine countries. Slightly more than half of the papers were prepared by authors who live outside the US and Canada.
Results of Gear Technology research on trends in employment, outsourcing, machine tool investment and other gear industry business practices.
Delta Research bets big on the future of gear-making technology.
Aachen has long been the center of European gear research.
Two high-volume gear production cells grace the shop floor at Delta Research Corporation in Livonia, Michigan. Thanks to lean manufacturing, these cells have never shipped a defective part to a customer since they were developed over three years ago.
Aerospace/Defense contracts offer unique challenges for gear manufacturers.
Gear-related new technology from Helios, Chiron, C-B Gear & Machine, Marposs, Dillon Manufacturing, Schunk, Forest City Gear and more.
The usage of modern thrusters allows combining the functions of the drive and the ship rudder in one unit, which are separated in conventional ship propulsion systems. The horizontally oriented propeller is supported in a vertically rotatable nacelle that is mounted underneath the ship's hull. The propeller can directly or indirectly be driven by an electric motor or combustion engine. Direct drive requires the installation of a low-speed electric motor in the nacelle. This present paper concentrates on indirect drives where the driving torque is transferred by bevel gear stages and shafts from the motor to the propeller.
Which transmission system will come out on top is a hot topic in the automotive community. With multiple transmission-centric conferences on the horizon, there will be plenty of debate, but how much will the answer actually affect gear manufacturers, and when?
Fraunhofer CMI focuses on new U.S. gear and transmission technologies group, plus other news from around the industry.