shop floor - Search Results
Articles About shop floor
Articles are sorted by RELEVANCE. Sort by Date.
Runout is a troublemaker! Good shop practice for the manufacture or inspection of gears requires the control of runout. Runout is a characteristic of gear quality that results in an effective center distance variation. As long as the runout doesn't cause loss of backlash, it won't hurt the function of the gear, which is to transmit smooth motion under load from one shaft to another. However, runout does result in accumulated pitch variation, and this causes non-uniform motion, which does affect the function of the gears. Runout is a radial phenomenon, while accumulated pitch variation is a tangential characteristic that causes transmission error. Gears function tangentially. It is also possible to have a gear with accumulated pitch variation, but little or no runout.
Questions: I have heard the terms "safety factor," "service factor," and "application factor" used in discussing gear design. what are these factors an dhow do they differ from one another? Why are they important?
Question: I have just become involved with the inspection of gears in a production operation and wonder why the procedure specifies that four involute checks must be made on each side of the tooth of the gear being produced, where one tooth is checked and charted in each quadrant of the gear. Why is this done? These particular gears are checked in the pre-shaved, finish-shaved, and the after-heat-treat condition, so a lot of profile checking must be done.
Revolutionary new inspection technologies are helping gear manufacturers develop and produce more complex, higher quality gears in a fraction of the time it used to take.
When designing hardened and ground spur gears to operate with minimum noise, what are the parameters to be considered? should tip and/or root relief be applied to both wheel and pinion or only to one member? When pinions are enlarged and he wheel reduced, should tip relief be applied? What are the effects on strength, wear and noise? For given ratios with enlarged pinions and reduced wheels, how can the gear set sized be checked or adjusted to ensure that the best combination has been achieved?
Photography is an essential part of gear failure analysis. It not only provides a fast, convenient way to accurately document the appearance of gear failure, but also is an effective diagnostic tool because the magnification obtained through photographic enlargement and slide projection often discloses evidence that may have been missed if the gears were not photographed.
We make a lot of single-start worm and worm gear sets, and it always seems as though we're buying another special hob. We also do a lot of spur gear cutting, and the spur gear hobs and the worm gear hobs look alike, so we wonder why we cannot use the standard hobs for cutting worm gears too. Can we do this?
Could the tip chamfer that manufacturing people usually use on the tips of gear teeth be the cause of vibration in the gear set? The set in question is spur, of 2.25 DP, with 20 degrees pressure angle. The pinion has 14 teeth and the mating gear, 63 teeth. The pinion turns at 535 rpm maximum. Could a chamfer a little over 1/64" cause a vibration problem?
How do we know when the gear material we buy is metallurgically correct? How can we judge material quality when all gear material looks alike?
In today's production environment, a variety of different measurement devices is used to assess the quality and accuracy of workpieces. These devices include CMMs, gear checkers, form testers, roughness testers, and more. It requires a high machine investment and a high handling effort - especially if a full end-of-line measurement is needed. One approach to reduce quality costs is to include all measurements in one single machine that is suitable and robust enough for use in production.
One of our readers in England has asked for our help in locating published technical data and information on the design, manufacture, and inspection of camshaft gears. Although millions of these gears have been made and are in constant use, we are not aware of any formal material having been published. We would be pleased to hear from anyone who had knowledge of such information.
Question: What is functional measurement and what is the best method for getting truthful answers?
Question: Do machines exist that are capable of cutting bevel gear teeth on a gear of the following specifications: 14 teeth, 1" circular pitch, 14.5 degrees pressure angle, 4 degrees pitch cone angle, 27.5" cone distance, and an 2.5" face width?
Two questions on hobbing cover the various types of hobs and their unusual names, as well as the importance of hob swivel angle.
When we have problems with gearset failure, a common diagnosis is misalignment. What exactly is that and how do we prevent it? The second most common "killer" of good gear sets is misalignment (dirt, or abrasive wear, is first). Gear teeth simply won't carry the load if they don't touch, and the portion that does touch has to carry an overload to make up for the missing contact area.
Question: When evaluating charts from a gear inspection machine, it is sometimes found that the full length of the profile traces vary, and that sometimes they are less than the length of active profile (above start of active profile-SAP) by up to 20%. This condition could be caused by a concentricity error between tooth grinding and shaping, or by unequal stock removal when grinding. (See Fig. 1.) Is it possible that some of the variation is coming from the inspection machine? How can variation from the inspection machine be reduced?
Question: Could you explain what is meant by "horological gearing"? I never heard of this before, although I understand it has something to do with watches. Could you also explain the meaning of a "going gear train"?
Question: When cutting worm gears with multiple lead stock hobs we find the surface is "ridged". What can be done to eliminate this appearance or is to unavoidable?
There's no substitute for a good software package in gear manufacturing. It's a critical shop floor tool that provides practical engineering services that customers appreciate. When you're in the business of specifying and procuring high quality gears, the software needs to meet many objectives including the consideration of all tolerances of center distance, tooth thickness and tip diameters, root diameters, fillets, etc. It's also imperative that the software updates include the latest revisions to the gear standards being used in the industry.
Klingelnberg presents the technical aspects of its roughness measurement system.
Schafer Gear Works greatly reduces gear inspection queue time and adds precious capacity by installing Gleason's new "shop-hardened" 300GMS P gear inspection system.
As in nearly all industries, more costeffective solutions are currently called for in the gear manufacturing industry.
It should be a point of pride that the gear industry is actually safer than most other metalworking industries.
The trend toward moving coordinate measuring machines to the shop floor to become an integral part of the manufacturing operations brings real time process control within the reach of many companies. Putting measuring machines on the shop floor, however, subjects them to harsh environmental conditions. Like any measuring system, CMMs are sensitive to any ambient condition that deviates from the "perfect" conditions of the metrology lab.
You're already a veteran of the computer revolution. Only you and your controller know how much money you've spent and only your spouse knows how many sleepless nights you've had in the last ten years trying to carve out a place in the brave new world of computerized gear manufacturing. PC's, CNCs, CAD, CAM, DNC, SPC, CMM: You've got a whole bowl of alphabet soup out there on the shop floor. Overall these machines have lived up to their promises. Production time is down, quality is up. You have fewer scrapped parts and better, more efficient machine usage.
It used to be that a shop with hustle and plenty of big, fast machines could thrive using a manual system. But no more. Today's economic environment requires more and more in the way of topnotch service and quick turnaround - which frequently means a completely integrated shop floor control system.
It's Monday morning, December 15, 2036. An autonomous vehicle drops off two engineers in front of a gear manufacturing facility in Metro Detroit. They punch in for work on their wristwatches and pay Uber for the ride on a smartphone. One of the engineers begins walking the shop floor, monitoring a series of collaborative robots using a tablet the size of a paperback novel. These robots interact right on the floor with the minimal staff scheduled to oversee manufacturing operations. Another engineer wears an interactive headset and begins training a group of new engineers (in real time) from China using some form of augmented reality.
The latest in machine tools, cutting tools, inspection equipment, shop floor gages and other products for the gear industry.
Nuttall Gear taps Machine Tool Builders for shop floor upgrades.
In this issue of Gear Technology, we are focusing on using computers to their greatest advantage in gear design and manufacturing. In a sense, that's old news. It's a cliche to suggest that computers make our work life easier and more productive. No company that wishes to remain competitive in today's global manufacturing environment can afford to be without computers in all their manifestations. We need them in the office; we need them next to our desks in place of drafting boards; we need them on the shop floor.
Compact, custom and portable solutions are gaining more attention in manufacturing today as companies seek out the tools that offer the greatest productivity gains on the shop floor. Gear inspection seems to be following suit.
New innovations in the management of hear treating parts washers and yielding powerful, unexpected benefits. Simply, cost effective shop floor practices are being combined in new ways to deliver big quality improvements and significant help to the bottom line. Employing these steps early in the process can dramatically cut waste hauling expenses and greatly reduce environmental liabilities while continuously producing cleaner parts.
When you have a multi-million-dollar transfer line sitting on the shop floor waiting for gears that might take up to two months to get, you have a costly bottleneck.
The "less is more" mantra is certainly a rallying cry in manufacturing. Technologies like multiaxis machining, 3D printing and automation are enabling companies to be more efficient, cost-conscious and flexible on the shop floor.
Shop floor inspection and gaging equipment is putting advanced metrology systems right on the factory floor. Hereâ€™s a collection of articles on shop floor inspection and gages from companies like Gleason, Mahr, Comtorgage, United Tool Supply and Frenco.
Temperature Induced Dimensional Changes Temperature causes various materials to change size at different rate, known as their Coefficients of Expansion (COE). The effects of this phenomenon on precision dimensional measurements are continuous and costly to industry. Precautions can be taken to allow parts and gages to temperature stabilize before conducting gage R & R studies, but the fact remains that on the shop floor temperatures vary all the time. The slow pace at which industry has accepted this reality probably has to do with the subtlety of these tiny size variations and our inability to sense gradual, but significant temperature changes.
With growing markets in aerospace and energy technologies, measuring hob cutters used in gear cutting is becoming an essential requirement for workpieces and machine tools. Zoller, a provider of solutions for tool pre-setters, measuring and inspection machines and tool management software, has developed a new partnership with Ingersoll/Germany for shop floor checking of hob cutters by a combined hardware and software approach.
This month, German automakers will receive the first three units of Klingelnberg's new automated blade checker designed for the shop floor.
Two high-volume gear production cells grace the shop floor at Delta Research Corporation in Livonia, Michigan. Thanks to lean manufacturing, these cells have never shipped a defective part to a customer since they were developed over three years ago.
The Corpus Clock has a hundred and one little interesting factoids about everything from its design to its unveiling to its message â€” and itâ€™s just hanging out on a street corner in Cambridge.
This is the first article in an eight-part "reality" series on implementing continuous improvement at Hoerbiger Corporation. Throughout 2013, Dr. Shahrukh Irani will report on his progress applying the job shop lean strategies he developed during his time at Ohio State University.
Why traditional lean manufacturing approaches need to be adapted for job shop environments.
Arrow Gear Company of Downers Grove, IL, has implemented a computer system that fully integrates exchange between all of its computer applications. The ELIMS (Electronic Linkage of Information Management Systems) project has increased manufacturing productivity and reduced lead times.
In the August issue, we examined the lean tools that will and will not work in high-mix, low-volume manufacturing facilities. Now, we will examine how to implement the tools that will work in the job shop with an approach that expands the capabilities of value stream mapping.
From time to time, the editors of "Shop Floor" receive correspondence from readers relating to particular articles they have written for past issues. As one of the purposes of this column is to provide a forum for the exchange of ideas, we reproduce here two of these letters and their replies. The subject of the first is the functional measurement of gears. (See Gear Technology, Sept/Oct, 1991, p. 17) Robert E. Smith writes the reply.
News Items About shop floor
1 Hexagon Introduces SF Shop Floor CMMs (February 19, 2014)
Hexagon Metrology recently announced the launch of the 7.10.7 SF, a new generation of shop floor coordinate measuring machines (CMMs) spe... Read News
2 Mitutoyo Introduces New Shop Floor CNC Machine (August 8, 2019)
Mitutoyo America Corporation is pleased to announce the release of the MiSTAR 555 CNC Shop Floor Coordinate Measuring Machine to its CMM ... Read News